Feeding the energy dashboard: whole-home monitoring hardware
Home Assistant's energy dashboard is only as honest as the meter feeding it — and a smart plug on the fridge is not a whole-home picture. Circuit-level monitoring (clamp CTs in your panel) shows the whole house and its biggest circuits in real time. Three hardware families dominate the HA world, with genuinely different philosophies. This guide compares them, explains the CT math that makes readings true, and lands the setup in the energy dashboard.
Published Nov 18, 2026
Safety first, briefly and seriously
Panel work is electrician territory. Clamp CTs are non-contact, but they live inside a panel that can kill you — and switching the main breaker off does not make the panel safe: in many residential panels, the service conductors feeding that breaker, and parts of the panel around them, remain energized even with the main breaker off. Unless you are properly trained and equipped for exactly this work, hire the install (it is a quick job for a pro) and do the software half yourself — that division of labor is common and smart. Everything below assumes the hardware is safely in; this guide is about choosing it and integrating it.
The three contenders
- Emporia Vue (Gen 2/3) — the value king: the meter plus a harness of CTs (up to 16 circuits on Gen 2 bundles) for less than rivals charge for the base unit. Cloud-first out of the box, BUT the ESPHome community flash turns it into a fully local device reporting straight to Home Assistant — the path this site recommends, with the caveat that flashing is a small hardware adventure (and Gen 3 details differ; check the ESPHome Vue project for your exact model).
- Shelly Pro 3EM — the DIN-rail professional: mounts in the panel, three phases (or three circuits) per unit, Ethernet + Wi-Fi, Shelly's mature local API and MQTT. Fewer circuits per dollar than the Vue, more 'install it and forget it for a decade' energy.
- IoTaWatt — the open-source measurement nerd's instrument: 14 inputs, superb accuracy, local logging with its own history, direct HA integration. Less plug-and-play, the most honest data of the three.
CT math: why readings lie and how to make them true
- Orientation matters: a CT clamp has a direction — reversed, the circuit reads negative. Every install guide's 'check the sign' step exists because everyone gets one backwards.
- Match the CT to the meter and the circuit — there is no universal sizing rule: each meter only accepts its own CT ecosystem. Emporia Vue: only Emporia's own CTs fit — 200A CTs (22 mm opening) on the mains ports, 50A CTs (10 mm opening) on the branch ports; that pairing comes with the bundle, not from a catalogue. Shelly: the EM takes Shelly's 50A or 120A CTs, but the 3EM and Pro 3EM accept only Shelly's 120A CT — Shelly explicitly does not support a 50A CT on them, and third-party CTs are not recommended. IoTaWatt: the flexible exception — you pick each CT from its supported list (50A, 100A, 200A and larger, from several makers) and configure it in setup. Whichever brand: the CT's range must cover the circuit's expected current, the clamp's opening must physically fit the conductor, and the exact supported CT models should be verified against the vendor's current documentation before buying. The grain of truth in the old '50A branches, 200A mains' shorthand is resolution — a CT sized far above its circuit (a 200A clamp watching a load that idles under an amp) reads poorly at low currents. Treat that as a consideration where a meter gives you a choice, not as a sizing law.
- Voltage reference: real power needs voltage × current × power factor. Meters that measure voltage directly (all three above do, via their power supply/reference) beat current-only estimates by a wide, bill-visible margin.
- Split-phase literacy (US panels): two 120V legs make 240V — mains CTs go one per leg, and 240V circuits (dryer, range, AC) need their CTs on the right legs or a dual-CT arrangement per the vendor's diagram. Follow the vendor diagram for your panel type exactly; this is not a vibes-based step.
Into Home Assistant
- Confirm each circuit's live reading against reality: kettle on, circuit jumps ~1,500 W; dryer on, the house notices. Mislabeled circuits announce themselves here — fix labels now, in the meter's config, before dashboards bake them in.
- Add the mains sensor as the energy dashboard's grid consumption (Settings → Dashboards → Energy), with circuit meters as individual devices — the dashboard's per-device breakdown is where the insight lives.
- Give it a week, then go hunting: the always-on baseline (many houses idle somewhere around 100–400 W, but treat that purely as an illustration, not a healthy-house standard — HVAC, water heating, pool equipment, dehumidifiers and always-on gear move a real baseline a long way, and a hot-climate home with a pool pump can sit far above it; measure your own overnight baseline, compare it across seasons, and treat every watt above your own normal as a mystery worth solving), the water heater's true cost, the 'vampire' circuit you did not expect.
- Feed the findings into automations — the energy chapter's patterns (our energy dashboard guide) assume exactly this data quality.
The verdict by household
Most circuits watched for least money, comfortable flashing: Emporia Vue + ESPHome. Set-and-forget professionalism, fewer circuits: Shelly Pro 3EM. Data fidelity above all: IoTaWatt. All three end at the same place — a Home Assistant that can finally answer 'what is using power right now, and what did it cost this month?' with numbers instead of gestures. Winter is when this hardware earns its keep: heating loads make every insight bigger, and the bill makes every insight welcome.
Gear for this build
Prices are editorial and change often; buttons show live prices. Some links may earn a commission at no cost to you — see the disclosure page.
Official documentation and references
- IoTaWatt documentation — installation, CT selection and configuration
- Shelly knowledge base — meter setup and CT clamp guidance
- Emporia support — Vue monitor installation and troubleshooting
- Home Assistant — the energy dashboard and how it consumes meter data
- Home Assistant — the Shelly integration
Frequently asked questions
Can I install panel CTs myself?
CT clamps are non-contact, but they install inside an electrical panel — and turning the main breaker off does not de-energize the whole panel: in many residential panels, the service conductors and parts of the panel remain live. Unless you are properly trained and equipped for this specific work, have a qualified electrician do the install; it is a quick job for a pro. This guide deliberately covers selection and integration, not panel procedure.
Is the Emporia Vue local or cloud?
Cloud by default — but the ESPHome community flash converts supported Vue models into fully local devices reporting to Home Assistant. Verify your exact model's flash support in the ESPHome Vue project before buying for that purpose.
How accurate are clamp meters?
Good ones land within a few percent of your utility meter — IoTaWatt is the accuracy reference of the three. Orientation, CT sizing and a real voltage reference are what separate honest readings from estimates.

